2011

Fused magnesia with a purity by weight of 97% or more

Proposed new wording:

Fused magnesia with a purity by weight of 94% or more

5503608/2016

5459963/2016

5503506/2016

5503114/2016

Methanol (CAS RN 67-56-1) with a purity by weight of 97% or more

Proposed new wording:

Methanol (CAS RN 67-56-1) with a purity by weight of 99,85% or more (as determined by the Methanol purity method IMPCA 001-14)

2011

1,4-Di(2-tert-butylperoxyisopropyl)benzene (CAS RN 25155-25-3)

Proposed new wording:

1,4-Di(2-tert-butylperoxyisopropyl)benzene (CAS RN 2781-00-2) or mixture of isomers 1,4-Di(2-tert-butylperoxyisopropyl)benzene and 1,3-di(2-tert-butylperoxyisopropyl)benzene (CAS RN 25155-25-3)

10849T

825537/ 2014

838627/ 2014

838774/ 2014

898981/ 2014

5654291/2016

1,2-Cyclohexanedicarboxylic acid, 1-butyl 2-(phenylmethyl) ester  (CAS RN 1200806-67-2)

nitro-benzonitrile (CAS RN 675126-26-8)

Colourant Reactive Black 5 (CAS RN 17095-24-8) and preparations based thereon with a colourant Reactive Black 5 content of 60 % or more but not more than 75 % by weight, and including one or more of the following:

·         Colourant Reactive Yellow 201 (CAS RN 27624-67-5),

·         1-Naphthalenesulphonicacid,4-amino-3-[[4-[[2-(sulphooxy)ethyl]sulphonyl]phenyl]azo]-, disodium salt (CAS RN 250688-43-8), or

·         3,5-diamino-4-[[4-[[2-(sulphooxy)ethyl]sulphonyl]fenyl]azo]-2-[[2-sulfo-4-[[2-(sulphooxy)ethyl]sulfonyl]phenyl]azobenzoic acid sodium salt (CAS RN 906532-68-1)

Proposed new wording:

Preparations based on colorant reactive black 5 (CAS RN 17095-24-8) containing 60 % or more by weight of this colorant, whether including or not, one or more of the following:

• Colorant Reactive Yellow 201 (CAS RN 27624-67-5),
• 1-Naphthalenesulphonicacid,4-amino-3-[[4-[[2-(sulphooxy)ethyl]sulphonyl]phenyl]azo]-, disodium salt (CAS RN 250688-43-8), or
• 3,5-diamino-4-[[4-[[2-(sulphooxy)ethyl]sulphonyl]fenyl]azo]-2-[[2-sulfo-4-[[2-(sulphooxy)ethyl]sulfonyl]phenyl]azobenzoic acid sodium salt (CAS RN 906532-68-1)

• o-amino polyisobutylenephenol (CAS RN 78330-13-9),
• more than 30% by weight but not more than 50% by weight of mineral oils,

used in the manufacture of blends of additives for lubricating oils (1)

• calcium long chain alkyltoluenesulphonates,
• calcium borate and
• more than 10% but not more than 40% by weight of mineral oils,

used in the manufacture of blends of additives for lubricating oils (1)

·         a magnesium salt of tetrapropylphenol and formaldehyde polymer,

·         more than 40% by weight but not more of 60% by weight of mineral oil,

·         having a total base number of more than 40 but not more than 100,

for use in the manufacture of blends of additives for lubricating oils (1)

Additives containing:

• a polyisobutylene succinimide based mixture, and
• more than 40 % but not more than 50 % by weight of mineral oils,

having a total base number of more than 40, for use in the manufacture of lubricating oils

Proposed new wording:

Additives containing:

·         a polyisobutylene succinimide based mixture, and

·         more than 30 % but not more than 50 % by weight of mineral oils,

having a total base number of more than 40, for use in the manufacture of lubricating oils

• polyisobutenyl succinic acid and
• more than 5% and not more than 20% by weight of mineral oils.

used in the manufacture of blends of additives for fuels (1)

• 1% or more but not more than 84% of caesium formate (CAS RN 3495-36-1), and
• 1% or more but not more than 75% of potassium formate (CAS RN 590-29-4)

with a density range of 1.57 sg or more but not more than 2.2 sg

• 1% or more but not more than 84% of caesium formate (CAS RN 3495-36-1), and
• 1% or more but not more than 76% of potassium formate (CAS RN 590-24-1)

• 25% or more but not more than of diethyl carbonate (CAS RN 105-58-8)
• 25% or more but not more than 50% of ethylene carbonate (CAS RN 96-49-1)
• 10% or more but not more than 20% of lithium hexafluorophosphate (CAS RN 21324-40-3)
• 5% or more but not more than 10% of ethyl methyl carbonate (CAS RN 623-53-0)
• 1% or more but not more than 2% of vinylene carbonate (CAS RN 872-36-6)
• 1% or more but not more than 2% of 4-fluoro-1,3-dioxolane-2-one (CAS RN 114435-02-8)
• Not more than 1% of 1,5,2,4-Dioxadithiane 2,2,4,4-tetraoxide (CAS RN 99591-74-9)

• 60 % or more but not more than 90 % by weight of 2-chloropropene (CAS RN 557-98-2),
• 8 % or more but not more than 14 % by weight of (Z)-1-chloropropene (CAS RN 16136-84-8),
• 5 % or more but not more than 23 % by weight of 2-chloropropane (CAS RN 75-29-6),
• not more than 6 % by weight of 3-chloropropene (CAS RN 107-05-1) and,
• not more than 1 % by weight of ethyl chloride (CAS RN 75-00-3)

• not more than 20 % of disodium sulphate, and
• not more than 10 % of sodium chloride

• 64 % or more, but not more than 74 % by weight of by weight of amorphous silica(CAS RN 7631-86-9)
• 25 % or more, but not more than 35 % by weight of butanone (CAS RN 78-93-3) and
• not more than 1 % by weight of 3-(2,3-epoxypropoxy)propyltrimethoxysilane (CAS RN 2530-83-8)

• with a crystalline structure,
• with a dominating participation of magnesia-alumina spinel and with admixtures of silicate phases and aluminates, at least 75 % by weight of which make fractions with a grain size of 1-3 mm and at most 25 % make fractions with a grain size of 0-1 mm

Mixture with a non-stoichiometric composition:

• with a crystalline structure,
• with a content of fused magnesia-alumina spinel and with admixtures of silicate phases and aluminates, at least 75 % by weight of which make fractions with a grain size of 1-3 mm and at most 25 % make fractions with a grain size of 0-1 mm

·         28% or more but not more than 32% of talc

·         43% or more but not more than 48% of silicon dioxide (quartz)

·         22% or more but not more than 26% of aluminium oxide

[for use in the manufacture of U-type glass fibre]

·         46% or more but not more than 51% of talc

·         30.5% or more but not more than 34.5% of silicon dioxide (quartz)

·         17.5% or more but not more than 20.5% of aluminium oxide

[for use in the manufacture of K-type glass fibre]

Solution of 2-chloro-5-(chloromethyl)-pyridine (CAS RN 70258-18-3) in Toluene

Proposed new wording:

Solution of 2-chloro-5-(chloromethyl)-pyridine (CAS RN 70258-18-3) in organic diluent

• urethane acrylates
• tripropylene glycoldiacrylate,
• ethoxylated bisphenol A acrylate or
• poly(ethyleneglycol) 400 diacrylate

22500T

point of more than 260°C, containing by weight:

·         15% or more but not more than 25% of polyethylene glycol

·         [- not more than 2% of methanol]

• 55% or more but not more than 65% of Vinyl terminated polydimethylsiloxane (CAS RN 68083-19-2 ),
• 30% or more but not more than 40% of Dimethylvinylated and trimethylated silica (CAS RN 68988-89-6 ),
• 1% or more but not more than 5% of Silicic acid, Sodium salt, reaction products with Chlorotrimethylsilane and Isopropyl alcohol (CAS RN 68988-56-7 )

5500T

Protein, chemically modified by carboxylation and/or phthalic acid addition, having a weight average molecular weight (M_w) of 100 000 to 300 000

Proposed new wording:

Protein, chemically or enzymatically modified by carboxylation and/or phthalic acid addition   and/or hydrolysis, having a weight average molecular weight (Mw) of less than 350 000

2008

• a tensile strength in the machine direction of 140 MPa or more but not more than 270 MPa and
• a tensile strength in the transverse direction of 20 MPa or more but not more than 40 MPa

as determined by test method ASTM D882/ISO 527-3

2009

461/7/

1999

• a thickness of 55 µm or more but not more than 97 µm
• a tensile modulus in the machine direction of 0,30 GPa or more but not more than 1,45 GPa, and
• a tensile modulus in the transverse direction of 0,20 GPa or more but not more than 0,70 GPa

·         a total thickness of more than 0,05mm but not more than 0,20 mm.

·         [a water entry pressure between 5 and 200 kPa according to the ISO 811 test method],

·         [an air permeability of 0,08 cm³/cm²/s or more according to the ISO 5636-5 test method]

• one flexible rubber hose;
• metal clips;
• whether or not of a resonator

for use in the manufacture of goods of Chapter 87

70195200

• of a width of 60 cm or more but not more than 160 cm, and
• with a thickness of 0,020 mm or more but not more than 0,260 mm

for use in the manufacture of prepregs

Fibreglass fabric

• E-glass filament
• (supplied) in rolls of a width of 60.0 cm or more, but not more than 160.0 cm,
• with a fibreglass fabric thickness of 0.020 mm or more, but not more than 0.260 mm,
• with a grammage of 15 g/m² or more, but not more than 220 g/m²

8530km

8507908060

8545909030

Roll of laminate foil of graphite and copper, with:

• a width of 610 mm or more but not more than 620 mm, and
• a diameter of 690 mm or more but not more than 710 mm,

for use in the manufacture of lithium-ion electric vehicle batteries

Proposed new wording:

Roll of laminate foil of graphite and copper, with:

• a width of 610 mm or more but not more than 620 mm, and
• a diameter of 690 mm or more but not more than 710 mm,

for use in the manufacture of lithium-ion electric batteries

385kT

130kT

100kT

8507908080

Sheet in the form of a roll consisting of a laminate of lithium and manganese bonded to aluminium, with:

• a width of 595 mm or more but not more than 605 mm, and
• a diameter of 690 mm or more but not more than 710 mm,

for use in the manufacture of cathodes for lithium-ion electric vehicle batteries

Proposed new wording:

Sheet in the form of a roll consisting of a laminate of lithium and manganese bonded to aluminium, with:

• a width of 595 mm or more but not more than 605 mm, and
• a diameter of 690 mm or more but not more than 710 mm,

for use in the manufacture of cathodes for lithium-ion electric batteries

Strip of aluminium alloy

Proposed new wording:

Plates, sheets and strip of an alloy of titanium

84073380

• with overall dimensions of not more than: 320 mm (length) x 381 mm (width) x 550 mm (height),
• a power of more than 22kW but not more than 35kW,
• equipped with output shaft having an end diameter of 30 mm and a taper of 6 degrees (+/- 1 degree)

for use in the manufacture of all-terrain vehicles (ATV) and utility task vehicles (UTV – side by side)

Single cylinder, four stroke internal combustion engine with a cylinder capacity of more than 325 cm3 but not more than 570 cm3,

• with overall dimensions of not more than: 320 mm (length) x 381 mm (width) x 550 mm (height),
• a power of more than 22kW but not more than 35kW,
• equipped with output shaft having an end diameter of 30 mm and a taper of 6 degrees (+/- 1 degree)

84073410

84073491

• with overall dimensions of not more than: 350 mm (length) x 480 mm (width) x 560 mm (height),
• a power of more than 44kW but not more than 130kW,
• equipped with output shaft having an end diameter of 30 mm and a taper of 6 degrees (+/- 1 degree)

for use in the manufacture of all-terrain vehicles (ATV) and utility task vehicles (UTV – side by side)

Dual cylinder, four stroke internal combustion engine with a cylinder capacity of more than 850 cm3 but not more than 1200 cm3,

• with overall dimensions of not more than: 350 mm (length) x 480 mm (width) x 560 mm (height),
• a power of more than 44kW but not more than 130kW,
• equipped with output shaft having an end diameter of 30 mm and a taper of 6 degrees (+/- 1 degree) or ended with a boss

8409990030

8411990070

• with a heat-resistance of not more than 1 050 °C,
• with a turbine wheel hole diameter of 30 mm or more, but not more than 110 mm,
• whether or not with an engine exhaust manifold

• camshaft position sensor (CMPS),
• inserts for counterparts assembly whether or not used for mounting wires,
• metal brackets for mounting to engine,
• two or more gaskets

for use in the manufacture of engines of motor vehicles

• manufactured from aluminum alloy
• with a diameter of 20 millimetres or more, but not more than 130 millimetres
• with a weight of 5 grams or more, but not more than 800 grams

2950k pieces

• having an outside diameter of 37mm,
• having an internal diameter of 25mm,
• supporting a maximum radial load of 4390N,
• supporting an axial load of 2990N

Synchronous motor for a dishwasher with a water flow control mechanism with

• a length without axle of 24 mm (+/- 0,3),
• a diameter of 49,3 mm (+/- 0,3)
• a rated voltage of 220 V AC or more but not more than 240 V AC,
• a rated frequency of 50 Hz or more but not more than 60 Hz
• an input power of not more than 4 W,
• a rotation speed of 4rpm or more but not more than 4,8rpm
• an output torque of not more than 10kgf/cm

Proposed new wording:

Synchronous motor for a dishwasher with a water flow control mechanism with

• a length without axle of 24 mm (+/– 0,3),
• a diameter of 49,3 mm (+/– 0,3),
• a rated voltage of 220 V AC or more but not more than 240 V AC,
• a rated frequency of 50 Hz or more but not more than 60 Hz,
• an input power of not more than 4 W,
• a rotation speed of 4 rpm or more but not more than 4,8 rpm
• an output torque of not less than 10 kgf/cm

• with a speed rotation of 7000 rounds/minute (without load),
• with a nominal voltage of 12V (+/- 4V),
• with a maximum power of 13.78W ( under 3.09A),
• with a specified temperature range from -40° to 160°,
• with a gear connection,
• with a mechanical attachment interface
• with 2 electrical connections,
• with a maximum torque of 100N.M

• with a speed rotation of 6500 rounds/minute (without load),
• with a nominal voltage of 12V (+/- 4V),
• with a maximal power below than 20 Watts,
• with a specified temperature range from -40° to 160°,
• with a worm gear drive
• with a mechanical attachment interface
• with 2 electrical connections
• with a maximum torque of 75N.M

Electric turbocharger actuator

·         a DC motor with an output of 10W or more but not more than 15W,

·         an integrated gear mechanism,

·         a (pulling)force of  250N or more at 160°C elevated ambient temperature,

·         a (pulling) force of 250N or more in each position of its stroke

·         an effective stroke of 15mm or more but not more than 20 mm,

·         with or without an on-board diagnostics interface

Proposed new wording:

Electric turbocharger actuator

·         a DC motor

·         an integrated gear mechanism,

·         a (pulling)force of 200 N or more at a minimum of 140 °C elevated ambient temperature,

·         a (pulling) force of 250 N or more in each position of its stroke,

·         an effective stroke of 15 mm or more but not more than 25 mm,

·         with or without an on-board diagnostics interface

• A rated power of more than 10 W but not more than 15 W,
• An insulation resistance of 100 M Ohms or more
• A DC resistance of not more than 34,8 Ohm (± 10%) at 20°C
• A rated current of not more than 1,22A
• A rated voltage of not more than 25V

2004

873/2005

Permanent magnets consisting of an alloy of neodymium, iron and boron, either in the shape of a rounded rectangle with

• a length of not more than 90 mm,
• a length of not more than 90 mm,
• a width of not more than 90 mm  and
• a height of not more than 55 mm,

or in the shape of a disc with a diameter of not more than 90mm, whether or not containing a hole in the centre

Proposed new wording:

Permanent magnets consisting of an alloy of neodymium, iron and boron, either in the shape of a rectangle, whether or not rounded, with a rectangular or a trapezoidal section having

• a length of not more than 140 mm,
• a width of not more than 90 mm  and
• a thickness of not more than 55 mm,

or in the shape of curved rectangle (tile type) having

• a length of not more than 75 mm,
• a width of not more than 40 mm,
• a thickness of not more than 7 mm and
• a radius of curvature of more than 86 mm but not more than 241 m

or in the shape of a disc with a diameter of not more than 90 mm, whether or not containing a hole in the centre.

A quarter sleeve, intended to become permanent magnet after magnetisation,

• consisting of at least neodymium, praseodym, iron, boron,

dysprosium, aluminium and cobalt,

• with a width of 9,2 mm (- 0,1
• with a length of 20 mm (+0,1) or 30 mm (+ 0,1)

of a kind used on rotors for the manufacture of fuel pumps

Proposed new wording:

A quarter sleeve intended to become permanent magnet after magnetization,

• consisting of at least neodymium, iron and boron,
• with a width of 9,1 mm or more but not more than  10,5 mm,
• with a length of 20 mm or more but not more than 30,1 mm,

of a kind used on rotors for the manufacture of fuel pumps.

2012

Bars specifically shaped, intended to become permanent magnets after magnetisation, containing neodymium, iron and boron, with dimensions:

·         a length of 15 mm or more but not more than 52 mm,

·         a width of 5 mm or more but not more than 42 mm,

of a kind to be used in the manufacture of electric servomotors for industrial automation

Proposed new wording:

A quarter sleeve, or a quarter sleeve with chamfered longitudinal edges, intended to become permanent magnets after magnetization,

• consisting of at least neodymium, holmium, dysprosium, boron and iron,
• with a width of 10,4 mm (+/- 0,1 mm) or 9,2 mm (- 0,1 mm),
• with a length of 20 mm (+ 0,1 mm) or 30 mm (+ 0,1 mm)

of a kind to be used in the manufacture of fuel pumps

2011

Cut plate of nickel-plated copper foil, with:

• a width of 70 mm (± 5 mm),
• a thickness of 0,4 mm (± 0,2 mm),
• a length of not more than 55 mm,

for use in the manufacture of lithium-ion electric vehicle batteries

Proposed new wording:

Cut plate of nickel-plated copper foil, with:

• a width of 70 mm (± 5 mm),
• a thickness of 0,4 mm (± 0,2 mm),
• a length of not more than 55 mm,

for use in the manufacture of lithium-ion electric batteries

–     50 W of power,

–     a power supply of more than 9 V but not more than 16 V,

–     an electrical impedance not more than 4 Ohm,

–     a sensitivity more than 80 dB

for use in the manufacture of motor vehicles

Holder, fixing item or internal stiffener of metal, for use in the manufacture of televisions, monitors and video players

Proposed new wording:

Metal holder, metal fixing item or internal stiffener of metal, for use in the manufacture of televisions, monitors and video players

LCD module with:

• a diagonal measurement of the screen of 14,5 cm or more but not more than 20,3 cm,
• or without a touch screen,
• an LED backlight,
• a printed circuit board with EEPROM, microcontroller, LVDS receiver and other active and passive components,
• a 12 pin plug for power supply and CAN and LVDS interfaces,
• in a housing with monitor and other control functions,

for installation in motor vehicles of chapter 87

Proposed new wording:

LCD module

·         with a diagonal measurement of the screen of 14,5 cm or more but not more than 38,5 cm,

·         straight or curved,

·         with or without a touch screen,

·         with an LED backlight,

·         with a printed circuit board with EEPROM, microcontroller, LVDS receiver and other active and passive components,

·         with a 12 pin plug for power supply and CAN and LVDS interfaces,

·         with or without electronic components for dynamic adjustments of colour,

·         in a housing, with or without mechanical, touch-sensitive or contactless control functions and with or without active cooling system,

suitable for installation in motor vehicles of chapter 87

2010

Colour LCD display panel for LCD monitors of heading 8528:

·         with a diagonal measurement of the screen of 14,48 cm or more but not more than 31,24 cm,

·         with backlight, micro-controller,

·         with a CAN (Controller area network)-controller with LVDS (Low-voltage differential signalling) interface and CAN/power supply socket or with an APIX (Automotive Pixel Link) controller with APIX interface,

·         in a housing with or without a heat sink at the back of the housing,

·         without a signal-processing module,

for use in the manufacture of vehicles of chapter 87

Proposed new wording:

Colour LCD display panel for LCD monitors of heading 8528:

• straight or curved,
• with a diagonal measurement of the screen of 14,48 cm or more but not more than 31,24 cm,
• with or without touch screen,
• with backlight, micro-controller,
• with a CAN (Controller area network)-controller with one or more LVDS (Low-voltage differential signalling) interfaces and one or more CAN/power supply sockets or with an APIX (Automotive Pixel Link) controller with APIX interface,
• in a housing with or without a heat sink at the back of the housing,
• without a signal-processing module,
• whether or not with haptic and acoustical feedback,

for use in the manufacture of vehicles of chapter 87

• with one or more single or multi-positional electrical switches (push-button, rotary or other),
• whether or not equipped with printed circuit boards and electrical cables,
• for a voltage of 9 V or more but not more than 16 V,
• for control module under the steering wheel, mounted on the steering column of motor vehicles of Chapter 87

• an antenna,
• a connector,
• a metal holder

for use in the manufacture of goods of Chapter 87

Antenna connecting cable for the transmission of analogue radio (AM/FM) and GPS signals, containing:

·         a coaxial cable,

·         two or more connectors,

·         3 or more plastic clips for attachment to the dashboard

of kind used in the manufacture of goods of Chapter 87

Proposed new wording:

Antenna connecting cable for the transmission of analogue radio (AM/FM) and GPS signals, containing:

• coaxial cable,
• two or more connectors,
• 3 or more plastic clips for attachment to the dashboard

of kind used in the manufacture of goods of Chapter 87

• a laser diode and a photodiode operating at a typical wavelength of 635 nm or more but not more than 815 nm
• an optical lens
• a “Recording Photodetector Integrated Circuit” (PDIC)
• a focussing and tracking actuator

• A pipe chassis for a three wheeled vehicle (TukTuk) containing an electric driven motor and in general containing an instrument panel and various body work parts;
• Roof and canvas
• Roll bar
• Wheels
• Back seat

equipped with among others:

• Seats
• 2 front wheels
• Electrical equipment
• Steering wheel and dashboard

87081090

87083091

Body of disc type brake in BIR (“Ball in Ramp”) or EPB (“Electronic Parking Brake”) version containing functional and mounting openings and guide grooves, of a kind used in the manufacture of goods of Chapter 87

Proposed new wording:

Body of disc type brake in BIR (“Ball in Ramp”), EPB (“Electronic Parking Brake”) version or  in  version with hydraulic function only, containing functional and mounting openings and guide grooves, of a kind used in the manufacture of goods of Chapter 87

8708405010

Automatic hydrodynamic gearbox with a hydraulic torque converter without transfer box, cardan shaft and front differential for use in the manufacture of motor vehicles of Chapter 87

Proposed new wording:

Automatic hydrodynamic gearbox

• with a hydraulic torque converter
• without transfer box and cardan shaft
• with or without front differential

for use in the manufacture of motor vehicles of Chapter 87

87088055

87089199

87089997

9001504930

• of a diameter of 4,9 cm or more but not more than 8,2 cm,
• of a height of 0,5 cm or more but not more than 1,8 cm

measured when the lens is laid on a flat surface from the horizontal plane to the lens front surface centre

of a kind used to be processed in order to be adapted to a pair of glasses

• a combination of one or more custom designed monolithic integrated circuits (ASIC) and
• at least one or more micro mechanic sensor element(s) (MEMS) with mechanic elements manufactured in semiconductor technology.
• ASIC and MEMS are mounted on top of each other in stack technology (stacked).